Avi-on Space
Sensor Coordinator

Space-Coordinator

Space Coordinator
FEATURES

Space Sensor Coordinator

The Space Sensor Coordinator unifies large, separately controlled sensor spaces to turn off in unison when the entire space is vacant. This adds predictability, security, and safety to an occupied space, while still leveraging the energy savings that come with sensor occupancy control.

Meets IECC 2018 multi-zone sensor coordination requirement

For larger spaces with multiple zones, sensors may leave lights on at a lower level, but after a set period of time when there is no occupancy in the full space, all the lights must turn off.

Simple configuration, all that is required is installing the Coordinator, add to the location, configure the zones to coordinate and the time delay to turn off.

Flexible Installation

The Space Sensor Coordinator is a different firmware version installed on an Avi-on XFAC hardware. There is no additional control wiring required. The unit wirelessly coordinates all sensors in the space. The functionality is packaged in a Class I Power Pack so that it is easy to install by installing on the outside of any convenient powered electrical box in the area and powering with 110-277V AC Power

Avi-on Direct Connect Sensors  Space Coordinator Datasheet (PDF)
Avi-on XPP Circuit-level Load Control
Avi-on Space Sensor Controller
Avi-on Direct Connect Sensors  Quick Set-up Guide (PDF)

Commercial Installation Guide  Commercial Installation Guide (PDF)

Space Coordinator
PARTS & ORDERING

Select a part number from the table listed below
Part NumberSupply VoltageChannelsConfiguration
AVI-SPACE-COORDINATOR100 - 277 VACN/AClass 1

To order please contact Avi-on sales at (877) AVION-US or prosales@avi-on.com
for information on becoming an Avi-on partner and order details.

Specifications

  • Supply Voltage US 100-277 VAC
  • Supply Voltage EU 220-240 VAC
  • Operating Current Consumption (100 VAC / 277 VAC) 20 / 14 81 / 46 mA
  • Operating Current Consumption (230 VAC) 14 46 mA
  • Output Voltage 0-10V_OUT 0.02 10.35 V
  • Storage Temperature -40/-40 +185/+85 °F/°C
  • Ambient Operating Temperature -4/-20 +113/+45 °F/°C
  • Relay Current (Electronic Ballast/LED Driver) – 16 A
  • Amperage for 0-10V lines 325 mA/CH

High Voltage Connections

  • AC Voltage (LINE) BLACK (AC LINE) AC 100-277VAC, #14
  • NEUTRAL WHITE AC neutral/common, #18
  • LINE DRIVER RED Relay controlled AC output (switched line), #14

Low Voltage Connections

  • 0-10V_OUT[1]+ PURPLE User controllable 0-10VDC (dimming), #18
  • 0-10V_OUT[2]+ ORANGE User controllable 0-10VDC (CCT), #18
  • 0-10V_OUT[1&2]- PINK Common dimming negative, #18
  • DC + 24V 62mA* Terminal 24 Volt DC output, #16-#24, Max 62mA
  • GND – Terminal Common ground, #16-#24
  • CC_IN Terminal 24 Volt Sensor input, #16-#24

Case Dimensions
Length 3.58” (91mm), Width 3.58” (91mm), Height 1.57” (40mm)

Protection/Immunity (non-regulatory): AC-input/user input and output connections: ESD Level-4 immunity per IEC/EN 61000-4-2

AC-input: EFT and BUSRTS immunity IEC/EN 61000-4-4, Class3 or better (=<2kV)

AC-input: SURGE immunity IEC/EN 61000-4-5, Class3 or better (=<2kV)

EU Regulatory
Over-voltage: Category III

Signal Indicator: LED ON Represents LOAD OFF

Glow-wire temperatures: 650°C /850°C
PCB Coating Type: Type 2

Certifications

  • USA 
    FCC ID: 2AFZI-AVIBG21
    FCC Part 15, Subpart B (Class B)
    FCC Part 15.247″
  • EU 
    BS EN IEC 55015:2019+A11:2020 / EN IEC 55015:2019+A11:2020
    BS EN 61547:2009 / EN 61547:2009
    BS EN IEC 61000-3-2:2019+A1:2021 / EN IEC 61000-3-2:2019+A1:2021
    BS EN 61000-3-3:2013+A2:2021 / EN 61000-3-3:2013+A2:2021
    ETSI EN 301 489-1 V2.2.3 (2019-11)
    ETSI EN 301 489-17 V3.2.4 (2020-09)
    BS EN IEC 61058-1:2018 / EN IEC 61058-1:2018
    BS EN 61058-1-2:2016 / EN 61058-1-2:2016
    BS EN 62479:2010 / EN 62479:2010
    BS EN 50663:2017 / EN 50663:2017
    ETSI EN 300 328 V2.2.2 (2019-11)
  • Canada
    IC ID: 20544-AVIBG21
    ICES-005, Issue 5, Dec. 2018
    RSS-GEN Issue 5, Feb. 2021 Amendment 2
    RSS-247 Issue 2, Feb. 2017
  • BQB
    DID: D059595
    Qualified Design ID (QDID): 185220
  • UL
    UL 60730-1 ED.5
    UL 2043 ED.4
    ALSO LISTED AS EMERGENCY LIGHTING EQUIPMENT (UL 924)

Avi-on
featured products

The Avi-on family of products consists of load controllers, sensors, wall stations and connectivity products that work together in one big happy family.  Load controllers manage dimming, schedules, scenes, groups/zones and more while the sensors are able to detect motion with all new state-of-the-art features. These products work seamlessly with the Av-ion cloud to provide a robust wireless ecosystem.